- SMULTRON 9.2.1 DOWNLOAD INSTALL
- SMULTRON 9.2.1 DOWNLOAD ARCHIVE
- SMULTRON 9.2.1 DOWNLOAD PATCH
- SMULTRON 9.2.1 DOWNLOAD ANDROID
If you have those, try this (paths may need correcting): (note the typo there in the chown line!) If you have logcat and journal error messages suggesting that RIL/ofono can't power the modem on and you have a qcom chipset, have a look in your for lines that power it on when the boot animation (bootanim) stops. (added automatically since ) Some devices (at least all hybris-13.0 based ports) have /dev/block/bootdevice/by-name/ as /dev/block structure in CM in which case you need to add the following line to the end of the les file in the last link:ĮNV" (added automatically since ) For devices with /dev/block/platform/msm_sdcc.1/by-name/ paths (msm_sdcc.1 can be different) add to $ANDROID_ROOT/rpm/ these paths and files with contents, and it most probably will help (but still paste your diff to the IRC channel): If you see differences you need to add custom udev rules to create the correct /dev/block structure
SMULTRON 9.2.1 DOWNLOAD ANDROID
Replicate /dev/block structure from Android as closely as possible (for rild to be able to access the modem partition)ĭiff the two outputs (this is WIP - android's toolbox ls might need more parameters to produce a comparable output) You can skip that by tapping on the each corner of the screen clockwise, while starting from left-top corner.Ĭellular Modem bringup is now in HADK v1.1.1 section 13.3 During the debugging process you will be building and flashing quite a few times, in which tutorial during the setup screen can be annoying. If it still crashes on gralloc or other gpu related bits, refer to WIP: Īdd this to $ANDROID_ROOT/rpm/droid-hal-$DEVICE.spec before the last line (do not change the last line, ever)Ĭongratulations if you have got gui working. Open("/sys/kernel/debug/tracing/trace_marker", O_WRONLY|O_LARGEFILE) = This error is known only on cm-10.1 base, and will be upstreamed to mer-hybris soon, but we need more tests: apply to this line and also apply If your apps are crashing (like on flo): Repeat the same for gralloc and copybit Once rebuilt, hwcomposer.*.so will be picked up and used by droid hal rebuild, and reside under /usr/libexec/droid-hybris/system/lib/hw Run `make hwcomposer.module_name` from results above
SMULTRON 9.2.1 DOWNLOAD INSTALL
If this command complains about missing column command run sudo apt-get install bsdmainutils)
SMULTRON 9.2.1 DOWNLOAD PATCH
If you're on display-legacy or display-caf(repo sync before 2015.06.04) patch hwcomposer withįrom HABUILD_SDK recompile android hwcomposer*.so for your deviceįind the name of the hwcomposer*.so module: run make modules | grep hwcomposer mk files starting from the primary BoardConfig.mk The repos included can be determined by looking at the -include device/$VENDOR/*/BoardConfig.mk or device/$VENDOR/*/BoardConfigCommon.mk lines at beginning the. It should be set to either caf or legacy. Look in any of the BoardConfig.mk or BoardConfigCommon.mk in any of the device repos for the device for the variable TARGET_QCOM_DISPLAY_VARIANT. If you get test_hwcomposer, minimer or lipstick segfault, or test_hwcomposer or minimer running but doing nothing (as on m7)Ĭheck if your device uses qcom_display-caf or display-legacy
SMULTRON 9.2.1 DOWNLOAD ARCHIVE
Test_hwcomposer should not be used as reliable hwc test!! if fails, then try minimer:Ĭurl -O # seems to currently give 404, the archive is mirrored at !AuDqiTFly4jxgxYNUdt16YluZn90ĮGL_PLATFORM=hwcomposer /usr/lib/qt5/bin/qmlscene -platform hwcomposer main.qml If strace dies after open("/sys/kernel/debug/tracing/trace_marker., perform You'll need to install strace to do so: zypper in strace Repo init -u git:///mer-hybris/android.git -b hybris-11.0 fails because of gpgĪs you follow steps below, strace any of the binaries that would fail for non-obvious reasons. If you're running an encrypted home partition with ecryptfs, you need to remount home anyway, even if nosuid flag is not set Just after chroot is entered through the `sdk` command, sudo fails to execute and fails with the previous messageĬheck for suid mount flag in the bind-mounted root: if your home (not chroot home) is mounted with nosuid you need to remount it before Sudo: effective uid is not 0, is sudo installed setuid root? USB tethering is now in HADK v1.1.1 section 9.2.3
Selinux and user session masking are now in HADK v1.1.1 section 9.2.1 So you booted your Sailfish OS? Congrats! No GUI? Oh dear :)īoth usb0 and rndis0 interfaces might be up, remove usb0 from init-script and rebuild kernel image with make hybris-boot or make hybris-recovery Please, do not use browser-in-place translation tools (right-click translate-this) or similar.
0 kommentar(er)
